Bathroom advice for High Wycombe homes

Why your bathroom goes mouldy, and what stops it for good

You spray it, scrub it, rinse it and admire the clean white sealant. Three weeks later the black dots are back in the same corners.

Mould in a bathroom is a symptom. Kill it without changing what feeds it and it returns every time. The good news is that the causes are few and well understood.

What mould needs

Mould spores are in the air of every home. They only grow where they find moisture that stays put. In a bathroom there are two sources.

The first is condensation. A hot shower fills the air with water vapour. When that air meets a cold surface, such as an outside wall, a window or a ceiling under a cold loft, the vapour turns back into water and sits there.

The second is water getting where it should not. A failed seal, cracked grout or a weeping pipe keeps the wall or floor damp from behind, and no amount of airing dries it.

Work out which you have and you are halfway to the cure.

What each mould pattern tells you

  • Black spots on the ceiling and high on outside walls. Condensation. Steam is rising and settling on the coldest surfaces.
  • Mould round the window frame and on the reveal. Condensation again, on the coldest spot in the room.
  • Black in the sealant along the bath or tray. Water is sitting in or behind the bead. The seal has failed or was never right.
  • Dark grout low down in the shower. Water is getting into the wall behind the tiles.
  • A musty smell from the bath panel, or mould on the skirting outside the bathroom. A leak under the bath or at the tray.
  • A stain on the ceiling below. A leak, and one that has been going for some time.

The first two are about air. The last four are about water escaping, and they need a fitter.

Curing condensation

The steam has to leave the room, and an open window on a January morning is not something a family keeps up. An extractor fan does the job without anyone having to remember.

Many bathroom fans are too weak, clogged with dust or ducted so badly that little air moves. Hold a sheet of toilet paper to the grille. If the fan will not hold it there, it is not doing much.

The Building Regulations in England ask for a fan in a new bathroom that extracts at least 15 litres of air a second. A good replacement is also quiet, so nobody switches it off, and runs on for some minutes after the light goes out. Some sense humidity and start themselves.

A new fan is the cheapest lasting cure on this page. The published price range for fitting one is in our bathroom cost calculator.

Warmth helps as well. A heated towel rail keeps the room above the temperature at which water settles, and a loft that is properly insulated over the bathroom stops the ceiling being the coldest thing in it.

Curing water behind the surface

If the sealant is black right through, cutting it out and resealing with the bath full of water may be all that is needed. Do it properly once.

If the mould is in the grout and tiles have begun to sound hollow, the backing is wet. Regrouting hides it for a season. The lasting repair is to take the tiles off that wall, replace the board with one made for wet areas, waterproof it and tile again. Our page on bathroom tiling in High Wycombe explains what should go behind a tile.

If there are signs of a leak under the bath or tray, stop using it if you can and have it looked at. The floor is getting wetter with every shower.

Why some High Wycombe bathrooms suffer more

Bathrooms that were added to the back of the old valley terraces often have three outside walls and a flat or lean-to roof. Every surface is cold, so steam condenses everywhere. These rooms need a strong fan and steady background heat more than any other.

Estate houses of the middle of the last century were mostly built with a small bathroom window and no fan. In those days the window was opened. A family of five showering one after another on a school morning puts far more water into that room than its builders had in mind.

And inside bathrooms in flats, with no window, depend entirely on the fan. When it fails, mould follows within weeks.

When to stop cleaning and refit

If you have a working fan, sound sealant and the mould still returns to the tiles, the room itself is the problem. The same goes for a bathroom where the plaster is soft, the floor gives underfoot or the paint peels off in sheets.

A refit lets the fitter cure all of it together: a new fan ducted properly, wet-area board and tanking, an insulated ceiling and surfaces with fewer joints to harbour growth. Read how the work is done on our page about bathroom installation in High Wycombe.

Common questions

Does anti-mould paint work in a bathroom?

It helps on a ceiling that suffers light condensation, because it resists growth on its own surface. It does nothing about the steam or about water coming through from behind. Used without a working fan, it simply delays the spots by a few months.

Why does the sealant round my bath keep going black?

Either water is pooling on the bead because the bath edge does not drain, or water has got behind the bead and is feeding mould from underneath. Mould that sits under the surface cannot be cleaned off. The sealant has to be cut out fully, the gap dried and a new bead applied with the bath full.

Find what is keeping the bathroom wet

Mould that keeps coming back is telling you that something stays wet. If it is steam, a fan ends it. If it is a leak, each shower adds to the damage in the wall or the floor, and the repair grows the longer it runs.

Say where the mould is and name your part of High Wycombe. Quotes are free.

Get a free bathroom quote

A minute of your time. No email address needed.

By sending this form you agree to your details being shared with a local bathroom fitter so they can contact you. See our privacy notice.

Get a free quote